Physical to Logical Port Assignment

1 Introduction

There are a variety of hardware LoadMaster models to choose from. For details on each, consult the Kemp website: www.kemptechnologies.com.

The physical network ports and their logical assignment varies between models depending on the underlying hardware platform used.

1.1 Document Purpose

This document provides details on all visible connections and indicators on each hardware LoadMaster. This includes outlining the total number of Ethernet and Small Form-factor Pluggable (SFP+) ports on each model. Because the physical port labels on each LoadMaster model may vary, this document shows the factory default logical port label assignment.  

1.2 Intended Audience

This document is intended to be read by anyone who is interested in finding out the logical port label assignment when installing a hardware LoadMaster.

2 Logical Port Label Assignment

Refer to the sections below for details on the logical port label assignment.

2.1 LoadMaster LM-X1

Port Location - Front Panel

LM-X1_front.png

Item No. Item Description Notes
1. PWR LED LED - Blue Power on indicator
    LED - Off Power off indicator
  HDD LED LED - Blinking amber Indicates HDD operating normal
    LED - Off Indicates no activity of HDD
2. Reset Reset LoadMaster Software reset
3. RJ45 console port RJ45 Console Connection Allows RJ45 console devices to connect to the system
4. USB Ports USB 3.0 Ports (x2) Allows USB devices to connect to the system
5. 1 Gb copper ethernet ports 1 Gigabit Ethernet (GbE) Copper (RJ45) ports (x4)

Logical Assignment
Port 0:3 map to ETH0:ETH3

    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)

Port Location - Rear Panel

LM-X1_rear.png

Item No. Item Description Notes
6. Video Graphics Array (VGA) port Standard VGA interface Used to connect a VGA monitor
7. Power supply 65W AC power supply Power source for the system, refer to item 1 for status LED Indicators.

2.2 LoadMaster LM-X3

Port Location - Front Panel

LM-X3FrontPanel.png

Item No. Item Description Notes
1. PB2 LED
PB1 LED
Not used
Not used
Not used
Not used
  PWR LED LED - Green Power on indicator
    LED - Off Power off indicator
  HDD LED LED - Blinking amber Indicates HDD activity
    LED - Off Indicates no HDD activity
2. Reset Reset LoadMaster Software reset
3. RJ45/Micro USB type console ports RJ45 Console Connection Allows RJ45 console devices to connect to the system
4. USB Ports USB 3.0 Ports (x2) Allows USB devices to connect to the system
5. 1 Gb copper ethernet ports 1 GbE copper (RJ45) ports (x8)

Logical Assignment
Port 0:7 map to ETH0:ETH7

    Activity LED - Blinking Indicates data activity
    Activity LED - Off Indicates no data activity
    Link LED - On Indicates data 1 Gb and 10/100 Mb
    Link LED - Off Indicates no link

Port Location - Rear Panel

LM-X3_rear.png

Item No. Item Description Notes
6. VGA Port Standard VGA interface Used to connect a VGA monitor
7. USB Ports USB 2.0 Ports (x2) Allows USB devices to connect to the system
8. Power switch Press to power-on or power-off the system On/off switch Press to power on or power off the system
9. Power supply 300W AC power supply Power source for the system, refer to item 1 for status LED Indicators.

2.3 LoadMaster LM-X15

Port Location - Front Panel

LM-X15FrontPanel.png

Item No. Item Description Notes
1. RAID (Dual HDD) RAID 0 (mirroring) Hot-Swap Disk (x2) Disk mirroring - replicating of data to two or more disks
    HDD LED - Green Indicates HDD operating normal
    HDD LED - Red Indicates possible HDD issue (contact Kemp Customer Support)
    Rebuild LED - Blinking amber Indicates HDD rebuilding process (could take several hours to complete)
2. PB2 LED
PB1 LED
Not used
Not used
Not used
Not used
  PWR LED LED - Green Power on indicator
    LED - Off Power off indicator
  HDD LED LED - Amber Indicates HDD activity
    LED - Off Indicates no HDD activity
3. Reset Reset LoadMaster Software reset
4. RJ45/Micro USB type console ports RJ45/micro USB type Console Connection Allows RJ45/micro USB console devices to connect to the system
5. USB Ports USB 3.0 Ports (x2) Allows USB devices to connect to the system
6. 1 Gb Ethernet ports 1 GbE copper (RJ45) ports (x16)

Logical Assignment
Port 0:15 map to ETH0:ETH15

    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)
7. 10 Gb Fiber SFP+ ports 10 Gbps Fiber SFP+ Ports (x4) Requires SFP+ modules (purchase from Kemp)
Logical Assignment
Port 16:19 map to ETH16:ETH19
    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)

Port Location - Rear Panel

image34.png

No Item Description Notes
8. VGA port Standard VGA interface Used to connect a VGA monitor
9. Power switch On/off switch Press to power on or power off the system
10. Dual Hot-Swap power supply 450W 1+1 redundant power supply Power source for the system, refer to item 2 for status LED Indicators.
    LED - Green Indicates power on mode
    LED - Blinking green Indicates standby mode
    LED - Blinking red with high pitch sound Indicates a loss of power supply redundancy and/or an issue with the power supply

2.4 LoadMaster LM-X15-MT

Port Location - Front Panel

LM-X15-MTFrontPanel.png

Item No. Item Description Notes
1. RAID (Dual HDD) RAID 0 (mirroring) Hot-Swap Disk (x2) Disk mirroring - replicating of data to two or more disks
    HDD LED - Green Indicates HDD operating normal
    HDD LED - Red Indicates possible HDD issue (contact Kemp Customer Support)
    Rebuild LED - Blinking amber Indicates HDD rebuilding process (could take several hours to complete)
2. PB2 LED
PB1 LED
Not used
Not used
Not used
Not used
  PWR LED LED - Green Power on indicator
    LED - Off Power off indicator
  HDD LED LED - Amber Indicates HDD activity
    LED - Off Indicates no HDD activity
3. Reset Reset LoadMaster Software reset
4. RJ45/Micro USB type console ports RJ45/micro USB type Console Connection Allows RJ45 console devices to connect to the system
5. USB Ports USB 3.0 Ports (x2) Allows USB devices to connect to the system
6. 1 Gb Ethernet Ports 1 GbE Copper (RJ45) Ports (x16) Logical Assignment
Port 0:15 map to ETH0:ETH15
    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Indicates no network activity
    Link LED - Off No link (cable disconnected)
7. 10 Gb Fiber SFP+ Ports 10 Gbps Fiber SFB+ Ports (x4) Requires SFP+ modules (purchase from Kemp)
Logical Assignment
Port 16:19 map to ETH16:ETH19
    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)

Port Location - Rear Panel

LM-X15-MT_rear.png

Item No. Item Description Notes
8. VGA port Standard VGA interface Used to connect a VGA monitor
9. Power switch On/off switch Press to power on or power off the system
10. Dual Hot-Swap power supply 450W 1+1 redundant power supply Power source for the system, refer to item 2 for status LED Indicators.
    LED - Green Indicates power on mode
    LED - Blinking green Indicates standby mode
    LED - Blinking red with high pitch sound Indicates loss of power supply redundancy and/or issue with power supply

2.5 LoadMaster LM-X25

Port Location - Front Panel

LM-X25FrontPanel.png

Item No. Item Description Notes
1. RAID (Dual HDD) RAID 0 (mirroring) Hot-Swap Disk (x2) Disk mirroring - replicating of data to two or more disks
    HDD LED - Green Indicates HDD operating normal
    HDD LED - Red Indicates possible HDD issue (contact Kemp Customer Support)
    Rebuild LED - Blinking amber Indicates HDD rebuilding process (could take several hours to complete)
2. ERR LED Error LED - Red Indicates if the system is experiencing an error during operation (contact Kemp Customer Support)
  STBY LED Standby LED - Amber Indicates that the system is in sleep mode
  HDD LED LED - Amber Indicates HDD activity
    LED - Off Indicates no HDD activity
  PWR LED LED - Green Power on indicator
    LED - Off Power off indicator
3. RJ45 console port RJ45 Console Connection Allows RJ45 console devices to connect to the system
4. USB Ports USB 3.0 Ports (x2) Allows USB devices to connect to the system
5. 1 Gb Ethernet Ports 1 GbE Copper (RJ45) Ports (x2)

Logical Assignment
Port 0:1 map to ETH0:ETH1

    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)
6. Reset Reset LoadMaster Software reset
7. 10Gb Fiber SFP+ Ports 10 Gbps SFP+ Ports (x12)

Logical Assignment
Port 2:13 map to ETH2:ETH13

    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)

Port Location - Real Panel

image37.png

Item No. Item Description Notes
8. VGA port Standard VGA interface Used to connect an VGA monitor
9. Power switch On/off switch Press to power on or power off the system
10. Dual Hot-Swap Power Supply 700W 1+1 redundant power supply Power source for the system, refer to item 2 for status LED Indicators.
    LED - Green Indicates power on mode
    LED - Blinking green Indicates standby mode
    LED - Amber Indicates loss of power supply redundancy and/or issue with power supply
11. USB Ports USB 2.0 Ports (x2) Allows USB devices to connect to the system

2.6 LoadMaster LM-X25-MT

Port Location - Front Panel

LM-X25-MTFrontPanel.png

Item No. Item Description Notes
1. RAID (Dual HDD) RAID 0 (mirroring) Hot-Swap Disk (x2) Disk mirroring - replicating of data to two or more disks
    HDD LED - Green Indicates HDD operating normal
    HDD LED - Red Indicates possible HDD issue (contact Kemp Customer Support)
    Rebuild LED - Blinking amber Indicates HDD rebuilding process (could take several hours to complete)
2. ERR LED Error LED - Red Indicates if the system is experiencing an error during operation (contact Kemp Customer Support)
  STBY LED Standby LED - Amber Indicates if the system is in sleep mode
  HDD LED LED - Amber Indicates HDD activity
    LED - Off Indicates no HDD activity
  PWR LED LED - Green Power on indicator
    LED - Off Power off indicator
3. RJ45 console port RJ45 Console Connection Allows RJ45 console devices to connect to the system
4. USB Ports USB 3.0 Ports (x2) Allows USB devices to connect to the system
5. 1 Gb Ethernet Ports 1 GbE Copper (RJ45) Ports (x2)

Logical Assignment
Port 0:1 map to ETH0:ETH1

    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)
6. Reset Reset LoadMaster Software reset
7. 10 Gb Fiber SFP+ Ports 10 Gbps SFP+ Ports (x12) Requires SFP+ modules (purchase from Kemp)
Logical Assignment
Port 2:13 map to ETH2:ETH13
    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)

Port Location - Real Panel

LM-X25-MT_rear.png

Item No. Item Description Notes
8. VGA port Standard VGA interface Used to connect a VGA monitor
9. Power switch On/off switch Press to power on or power off the system
10. Dual Hot-Swap Power Supply 700W 1+1 redundant power supply Power source for the system, refer to item 2 for status LED Indicators.
    LED - Green Indicates power on mode
    LED - Blinking green Indicates standby mode
    LED - Amber Indicates loss of power supply redundancy and/or an issue with the power supply
11. USB Ports USB 2.0 Ports (x2) Allows USB devices to connect to the system

2.7 LoadMaster LM-X40

Port Location - Front Panel

LM-X40FrontPanel.png

Item No. Item Description Notes
1. RAID (Dual HDD) RAID 0 (mirroring) Hot-Swap Disk (x2) Disk mirroring - replicating of data to two or more disks
    HDD LED - Green Indicates HDD operating normal
    HDD LED - Red Indicates possible HDD issue (contact Kemp Customer Support)
    Rebuild LED - Blinking amber Indicates HDD rebuilding process (could take several hours to complete)
2. ERR LED Error LED - Red Indicates that the system is experiencing an error during operation (contact Kemp Customer Support)
  STBY LED Standby LED - Amber Indicates that the system is in sleep mode
  HDD LED LED - Amber Indicates HDD activity
    LED - Off Indicates no HDD activity
  PWR LED LED - Green Power on indicator
    LED - Off Power off indicator
3. RJ45 console port RJ45 Console Connection Allows RJ45 console devices to connect to the system
4. USB Ports USB 3.0 Ports (x2) Allows USB devices to connect to the system
5. 1 Gb Ethernet Ports 1 GbE Copper (RJ45) Ports (x2)

Logical Assignment
Port 0:1 map to ETH0:ETH1

    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)
6. Reset Reset LoadMaster Software reset
7. 10 Gb Fiber SFP+ Ports 10 Gbps SFP+ Ports (x12) Requires SFP+ modules (purchase from Kemp)
Logical Assignment
Port 2:13 map to ETH2:ETH13
    Activity LED - Blinking Indicates network activity
    Activity LED - Off Indicates no network activity
    Link LED - On Link - connection established
    Link LED - Off No link (cable disconnected)

Port Location - Real Panel

image38.png

Item No. Item Description Notes
8. VGA port Standard VGA interface Used to connect a VGA monitor
9. Power switch On/off switch Press to power on or power off the system
10. Dual Hot-Swap Power Supply 700W 1+1 redundant power supply Power source for the system, refer to item 2 for status LED Indicators.
    LED - Green Indicates power on mode
    LED - Blinking green Indicates standby mode
    LED - Amber Indicates loss of power supply redundancy and/or issue with power supply
11. USB ports USB 2.0 Ports (x2) Allows USB devices to connect to the system
 

2.8 LoadMaster LM-X40-MT

Port Location - Front Panel

LM-X40-MTFrontPanel.png

 

Item No.ItemDescriptionNotes
1.RAID (Dual HDD)RAID 0 (mirroring) Hot-Swap Disk (x2)Disk mirroring - replicating of data to two or more disks
  HDD LED - GreenIndicates that the HDD is operating normally
  HDD LED - RedIndicates a possible HDD issue (contact Kemp Customer Support)
  Rebuild LED - Blinking amberIndicates HDD rebuilding process (could take several hours to complete)
2.ERR LEDError LED - RedIndicates that the system is experiencing an error during operation (contact Kemp Customer Support)
 STBY LEDStandby LED - Amber Indicates that the system in sleep mode
 HDD LEDLED - AmberIndicates HDD activity
  LED - OffIndicates no HDD activity
 PWR LEDLED - Green Power on indicator
   LED - OffPower off indicator
3.RJ45 console port RJ45 Console ConnectionAllows RJ45 console devices to connect to the system
4.USB PortsUSB 3.0 Ports (x2) Allows a USB device to connect to the system
5.1 Gb Ethernet Ports 1 GbE Copper (RJ45) Ports (x2)

Logical Assignment
Port 0:1 map to ETH0:ETH1

  Activity LED - Blinking Indicates network activity
  Activity LED - Off Indicates no network activity
   Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)
6.ResetReset LoadMaster Software reset
7.10 Gb Fiber SFP+ Ports10 Gbps SFP+ Ports (x12) Requires SFP+ modules (purchase from Kemp)
Logical Assignment
Port 2:13 map to ETH2:ETH13
  Activity LED - BlinkingIndicates network activity
  Activity LED - OffIndicates no network activity
  Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)

Port Location - Rear Panel

LM-X40-MT_rear.png

Item No.ItemDescriptionNotes
8.VGA portStandard VGA interfaceUsed to connect a VGA monitor
9.Power switchOn/off switch Press to power on or power off the system
10.Dual Hot-Swap Power Supply700W 1+1 redundant power supply Power source for the system, refer to item 2 for status LED Indicators.
  LED - GreenIndicates power on mode
  LED - Blinking greenIndicates standby mode
  LED - AmberIndicates loss of power supply redundancy and/or issue with power supply
11.USB Ports USB 2.0 (x2) Allows USB devices to connect to the system

2.9 LoadMaster LM 8020-FIPS

Port Location - Front Panel

image42.png

Item No.ItemDescriptionNotes
1.Power on indicator/Power buttonLED - GreenIndicates power on
  LED - OffIndicates power off
2.NMI buttonNot usedNot used
3.System identification buttonLED - Blinking When pressed on either the front or rear panel, it flashes to locate the system in the rack. Press the button again to stop flashing.
4.VGA PortStandard VGA interfaceUsed to connect a VGA monitor
5.LCD Menu buttons Allows you to navigate the control panel LCD menu  
5a.LCD Left button Moves the cursor back in one-step increments  
5b.LCD Select button Selects the menu item highlighted by the cursor  
5c.LCD Right button Moves the cursor forward in one-step increments  
6.LCD panel Displays the system ID, status information, and system error messages  
   LCD backlight BlueIndicates normal system operation
  LCD backlight Amber Indicates system error and displays the error code
  LCD backlight OffIndicates system in standby mode. You can turn it on by pressing any of the LCD Menu buttons.
7.SD card slot for vFlash Not usedNot used
8.USB PortsUSB 2.0 Ports (x2) Allows you to connect USB devices to the system
9.System service tag A slide out label indicating the system service tag, MAC address, and NIC 

Port Location - Back Panel

Item No.ItemDescriptionNotes10.System identification button LED - Blinking When pressed on either the front or rear panel, flashes to locate the system in the rack. Press the button again to stop flashing. 11.System identification connector Not usedNot used12.iDRAC8 port Not usedNot used13.10Gb Fiber SFP+ Ports 10Gb SFP+ Ports (x2) Requires SFP+ modules (purchase from Kemp) Logical AssignmentPort 6:7 map to ETH6:ETH7   Activity LED - BlinkingIndicates network activity   Activity LED - OffIndicates no network activity   Link LED - OnLink - connection established  Link LED - OffNo link (cable disconnected)14.Serial Console Port Serial console data interfaceUsed to connect a serial crossover cable to a console15.VGA Port Standard VGA interface Used to connect a VGA monitor16.USB PortsUSB 2.0 Ports (x2)Allows USB devices to connect to the system17.10Gb Fiber SFP+ Ports 10 Gb SFP+ Ports (x2) Requires SFP+ modules (purchase from Kemp) Logical AssignmentPort 2:5 map to ETH2:ETH5   Activity LED - BlinkingIndicates network activity   Activity LED - OffIndicates no network activity    Link LED - OnLink - connection established  Link LED - OffNo link (cable disconnected)18.10Gb Fiber SFP+ Ports 10 Gb SFP+ Ports (x2) Requires SFP+ modules (purchase from Kemp) Logical AssignmentPort 1:0 map to ETH1:ETH0   Activity LED - BlinkingIndicates network activity   Activity LED - OffIndicates no network activity   Link LED - OnLink - connection established  Link LED - OffNo link (cable disconnected)19.Dual Hot-Swap Power Supply 750W 1+1 redundant power supply Power source for the system, refer to item 1 for status LED Indicators.  LED - GreenIndicates operating mode  LED - Blinking amberIndicates fault mode

2.10 LoadMaster LM-8020 and LM-8020M

Port Location - Front Panel

LM-8020_and_LM-8020M_front.png

Item No.ItemDescriptionNotes
1.Power on indicator/power button LED - Green Indicates power on
  LED - OffIndicates power off
2.NMI buttonNot usedNot used
3.System identification buttonLED - Blinking When pressed on either the front or rear panel, it flashes to locate the system in the rack. Press the button again to stop flashing.
4.VGA PortStandard VGA interface Used to connect a VGA monitor
5.LCD Menu buttons Allows you to navigate the control panel LCD menu  
5a.LCD Left button Moves the cursor back in one-step increments  
5b.LCD Select button Selects the menu item highlighted by the cursor  
5c.LCD Right button Moves the cursor forward in one-step increments  
6.LCD panel Displays the system ID, status information, and system error messages.  
   LCD backlight BlueIndicates normal system operation
  LCD backlight AmberIndicates a system error and displays the error code
  LCD backlight OffIndicates that the system is in standby mode. You can turn the system on by pressing any of the LCD Menu buttons.
7.SD card slot for vFlash Not usedNot used
8.USB PortsUSB 2.0 Ports (x2)Allows you to connect USB devices to the system
9.System service tag A slide out label indicating the system service tag, MAC address, and NIC.  

Port Location - Rear Panel

LM-8020andLM-8020MRearPanel.png

Item No.ItemDescriptionNotes
10.System identification button LED - Blinking When pressed on either the front or rear panel, it flashes to locate the system in the rack. Press the button again to stop flashing.
11.System identification connector Not usedNot used
12.iDRAC8 port Not usedNot used
13.10 Gb Fiber SFP+ Ports 10 Gb SFP+ Ports (x2) Requires SFP+ modules (purchase from Kemp)
Logical Assignment
Port 6:7 map to ETH6:ETH7
  Activity LED - BlinkingIndicates network activity
  Activity LED - OffIndicates no network activity
  Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)
14.Serial Console Port Serial console data interface Used to connect a serial crossover cable to a console
15.VGA port Standard VGA interface Used to connect a VGA monitor
16.USB PortsUSB 2.0 Ports (x2)Allows USB devices to connect to the system
17.10 Gb Fiber SFP+ Ports 10 Gb SFP+ Ports (x4) Requires SFP+ modules (purchase from Kemp)
Logical Assignment
Port 5:4 map to ETH5:ETH4
  Activity LED - BlinkingIndicates network activity
  Activity LED - OffIndicates no network activity
   Link LED - OnLink - connection established
 Link LED - OffNo link (cable disconnected)
18.10 Gb Fiber SFP+ Ports 10 Gb SFP+ Ports (x2)

Logical Assignment
Port 0:4 map to ETH0:ETH4

  Activity LED - BlinkingIndicates network activity
  Activity LED - OffIndicates no network activity
  Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)
19.Dual Hot-Swap Power Supply 750W 1+1 redundant power supplyPower source for the system, refer to item 1 for status LED Indicators.
  LED - GreenIndicates operating mode
  LED - Blinking amberIndicates fault mode

2.11 LoadMaster LM-8000 and 8010-MT

Port Location - Front Panel

image27.png

Item No.ItemDescriptionNotes
1.Power on indicator/power buttonLED - GreenIndicates power on
  LED - OffIndicates power off
2.NMI buttonNot usedNot used
3.System identification buttonLED - Blinking When pressed on either the front or rear panel, flashes to locate the system in the rack. Press the button again to stop flashing.
4.VGA PortStandard VGA interfaceUsed to connect a VGA monitor
5.LCD Menu buttons Allows you to navigate the control panel LCD menu  
5a.LCD Left button Moves the cursor back in one-step increments  
5b.LCD Select button Selects the menu item highlighted by the cursor  
5c.LCD Right button Moves the cursor forward in one-step increments  
6.LCD panel Displays system ID, status information, and system error messages.  
   LCD backlight Blue Indicates normal system operation
  LCD backlight Amber Indicates system error and displays the error code
  LCD backlight offIndicates system in standby mode. Turn on by pressing any of the LCD Menu buttons.
7.SD card slot for vFlash Not usedNot used
8.USB PortsUSB 2.0 Ports (x2)Allows you to connect USB devices to the system
9.System service tag A slide out label indicating the system service tag, MAC address, and NIC.  

Port Location - Rear panel

LM-8000andLM-8010-MTRearPanel.png

Item No.ItemDescriptionNotes
10.System identification button LED - Blinking When pressed on either the front or rear panel, it flashes to locate the system in the rack. Press the button again to stop flashing.
11.System identification connector Not usedNot used
12.iDRAC8 port Not usedNot used
13.Serial Console Port Serial console data interfaceUsed to connect a serial crossover cable to a console
14.VGA Port Standard VGA interfaceUsed to connect a VGA monitor
15.USB Ports USB 2.0 Ports (x2)Allows USB devices to connect to the system
16.10 Gb Fiber SFP+ Ports 10 SFP+ Ports (x4)

Requires SFP+ modules (purchase from Kemp)

Logical Assignment
Port 4:5 map to ETH4:ETH5

  Activity LED - BlinkingIndicates network activity
  Activity LED - OffIndicates no network activity
   Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)
17.10 Gb Fiber SFP+ Ports 10 Gbps SFP+ Ports (x4)

Requires SFP+ modules (purchase from Kemp)

Logical Assignment
Port 0:3 map to ETH0:ETH3

  Activity LED - BlinkingIndicates network activity
  Activity LED - OffIndicates no network activity
  Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)
18.Dual Hot-Swap Power Supply 495W 1+1 redundant AC power supply Power source for the system, refer to item 1 for status LED Indicators.
  LED - GreenIndicates operating mode
  LED - Blinking amberIndicates fault mode

2.12 LoadMaster LM-5600 and LM-5610-MT

Port Location - Front Panel

LM-5600.png

Item No.ItemDescriptionNotes
1.Power on indicator/power buttonLED - GreenIndicates power on
  LED - OffIndicates power off
2.NMI buttonNot usedNot used
3.System identification buttonLED - BlinkingWhen pressed on either the front or rear panel, it flashes to locate the system in the rack. Press the button again to stop flashing.
4.VGA PortStandard VGA interfaceUsed to connect a VGA monitor
5.Diagnostic indicatorThe diagnostic indicator lights up to display error status  
6.USB PortsUSB 2.0 Ports (x2)Allows you to connect USB devices to the system
7.System service tag A slide out label indicating the system service tag, MAC address, and NIC 

Port Location - Rear Panel

LM-5600andLM5610-MTRearPanel.png

Item No.ItemDescriptionNotes
8.Serial Console Port Serial console data interfaceUsed to connect a serial crossover cable to a console
9.VGA PortStandard VGA interfaceUsed to connect a VGA monitor
10.1 Gb Ethernet ports

1 GbE Copper (RJ45) Ports (x2)

Logical Assignment
Port 0:1 map to ETH0:ETH1
  Activity LED - BlinkingIndicates network activity
  Activity LED - OffIndicates no network activity
  Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)
11.USB PortsUSB 2.0 Ports (x2)Allows USB devices to connect to the system
12.System status indicator LED - Blue Indicates normal system operation
  LED - Amber blinkingIndicates that the system has an error and needs attention
13.System identification buttonLED - Blinking When pressed on either the front or rear panel, flashes to locate the system in the rack. Press the button again to stop flashing.
14.1 Gb Ethernet Ports

1 GbE Copper (RJ45) ports (x2)

Logical Assignment
Port 2:3 map to ETH2:ETH3
  Activity LED - Blinking Indicates network activity
  Activity LED - OffIndicates no network activity
  Link LED - OnLink - connection established
  Link LED - Off No link (cable disconnected)
15.10 Gb Fiber SFP+ Ports

10 Gbps Fiber SFP+ Ports (x2)

Requires SFP+ modules (purchase from Kemp)

Logical Assignment
Port 4:5 map to ETH4:ETH5

  Activity LED - Blinking Indicates network activity
 Activity LED - OffIndicates no network activity
  Link LED - On Link - connection established
  Link LED - OffNo link (cable disconnected)
16.Dual Hot-Swap Power Supply 550W 1+1 redundant power supplyPower source for the system, refer to item 1 for status LED Indicators.
  LED - GreenIndicates operating mode
  LED - Blinking amberIndicates fault mode

2.13 LoadMaster LM-4000

Port Location - Front Panel

image23.png

Item No.ItemDescriptionNotes
1.Power on indicator/power buttonLED - GreenIndicates power on
  LED - offIndicates power off
2.NMI buttonNot usedNot used
3.VGA portStandard VGA interfaceUsed to connect a VGA monitor
4.Health indicatorLED - BlueIndicates the system is on and in good health
  LED - Blinks AmberIndicates the system is on and an error exits or the system is in standby mode
5.Hard-drive Indicator LED - Blinking greenIndicates hard drive activity
6.Electrical indicator LED - Blinking amber Indicates an electrical error such as a failed power supply or voltage out of range
7.Temperature indicator LED - Blinking amberIndicates a thermal error such as a fan failure or temperature out of range
8.System status indicator LED - Blue Indicates normal system operation
  LED - Blinks amberIndicates the system has an error and needs attention
9.System identification buttonWhen pressed on either the front or rear panel, it flashes to locate the system in the rack. Press the button again to stop flashing.  
10.USB Ports USB 2.0 Ports (x2)Allows USB devices to connect to the system
11.System service tag A slide out label indicating the system service tag, MAC address, and NIC.  
12.DVD optical drive (will not be included in any future orders) Optional SATA DVD +/- RW drive  

Port Location - Rear Panel

LM-4000RearPanel.png

Item No.ItemDescriptionNotes
13.Serial Console Port Serial console data interfaceUsed to connect a serial crossover cable to a console
14.10 Gb Fiber SFP+ Ports

10 Gbps Fiber SFP+ Ports (x2)

Requires SFP+ modules (purchase from Kemp)

Logical Assignment
Port 2:3 map to ETH2:ETH3

 Activity LED - BlinkingIndicates network activity
  Activity LED - OffIndicates no network activity
 Link LED - On Link - connection established
  Link LED - OffNo link (cable disconnected)
15.VGA PortStandard VGA interfaceUsed to connect a VGA monitor
16.eSATA + USB Ports

eSATA port (x1)

Allows to connect to additional storage devices

  USB 2.0 ports (x2)Allows you to connect USB devices to the system
17.1 Gb Ethernet ports

1 GbE Copper (RJ45) Ports (x2)

Logical Assignment
Port 0:1 map to ETH0:ETH1
  Activity LED - Blinking Indicates network activity
  Activity LED - OffIndicates no network activity
  Link LED - OnLink - connection established
  Link LED - Off No link (cable disconnected)
18.System status indicator LED - Blue Indicates normal system operation
  LED - Amber blinkingIndicates the system has an error and needs attention
19.System identification buttonLED - Blinking When pressed on either the front or rear panel, it flashes to locate the system in the rack. Press the button again to stop flashing.
20.Power supply 250W AC power supply Power source for the system, refer to item 1 for status LED Indicators.
21.Retention clip to secure power cable Secures the power cable  

2.14 LoadMaster LM-3400

Port Location - Front Panel

LM-3400FrontPanel.png

Item No.ItemDescriptionNotes
1.ResetReset LoadMaster Software reset
2.RJ45 Console Port RJ45 Console ConnectionAllows RJ45 console devices to connect to the system
3.USB PortsUSB 2.0 Ports (x2) Allows USB devices to connect to the system
4.1 Gb Ethernet Ports 1 GbE Copper (RJ45) Ports (x8)

Logical Assignment
Port 0:7 map to ETH0:ETH7

   Activity LED - Blinking Indicates network activity
  Activity LED - Off Indicates no network activity
   Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)
5.PWR LEDLED - GreenPower on indicator
  LED - OffPower off indicator
 SSD LEDLED - Amber blinkingIndicates read/write activity of the SSD
  LED - OffIndicates no activity of SSD

Port Location - Rear Panel

image40.png

Item No.ItemDescriptionNotes
6.VGA PortStandard VGA interfaceUsed to connect a VGA monitor
7.USB PortsUSB 2.0 Ports (x2) Allows USB devices to connect to the system
8.Power supply200W AC power supply Power source for the system, refer to item 5 for status LED Indicators.
9.Power switchOn/off switchPress to power on or power off the system

2.15 LoadMaster LM-3000

Port Location - Front Panel

LM-3000_front.png

Item No.ItemDescriptionNotes
1.ResetReset LoadMaster Software reset
2.RJ45 console port RJ45 Console ConnectionAllows RJ45 console devices to connect to the system
3.USB Ports USB 2.0 Ports (x2)Allows USB devices to connect to the system
4.1 Gb Ethernet Ports 1 GbE Copper (RJ45) Ports (x4)

Logical Assignment
Port 0:3 map to ETH0:ETH3

   Activity LED - Blinking Indicates network activity
  Activity LED - Off Indicates no network activity
   Link LED - OnLink - connection established
  Link LED - OffNo link (cable disconnected)
5.PWR LEDLED - GreenPower on indicator
  LED - OffPower off indicator
 SSD LEDLED - Amber blinkingIndicates read/write activity of the Solid State Disk (SSD)
  LED - OffIndicates no activity of the SSD

Port Location - Rear Panel

LM-3000_rear.png

Item No.ItemDescriptionNotes
6.VGA PortStandard VGA interface Used to connect a VGA monitor
7.USB Ports USB 2.0 Ports (x2) Allows USB devices to connect to the system
8.Power supply 200W AC power supply Power source for the system, refer to item 5 for status LED Indicators.
9.Power switch On/off switchPress to power on or power off the system

Last Updated Date

This document was last updated on 03 March 2020.

Was this article helpful?

0 out of 1 found this helpful

Comments

Avatar
netadmin

And where is the advertised "Physical to Logical Port Assignment"-matrix?
Not a single word about eth0, eth1, .... on the entire page here. :(

Avatar
Kemp Knowledge Team

Thanks for your comment. We are actually working on these updates as we speak and we hope to get an updated version of this document released soon.