KVM
Contents
1 Introduction
This document describes the installation of Kemp 360 Central in a Kernel-based Virtual Machine (KVM) environment.
There are several different versions of the VM available. Full details of the currently supported versions are available on our website: www.kemptechnologies.com.
Kemp 360 Central has been tested with UbuntuVersion 16.04.2 and KVM Version 2.5.0. For a full list of the KVM-compatible Linux distributions, refer to http://www.linux-kvm.org/page/Main_Page
If you have any issues with the VM when using different Linux distributions, contact Kemp Support.
2 Installing Kemp 360 Central on a KVM Environment
The following instructions describe how to install Kemp 360 Central in a KVM environment.
2.1 Download the KVM Files
The VM is packaged within a tar.gz file for ease of deployment. To download the VM, follow the instructions below:
1. Go to https://kemptechnologies.com/kemp360-central-download/.
2. Select your country from the drop-down list provided.
3. In the Select your hypervisor section, click KVM/XEN.
4. Click Download. A dialog box that allows you to save the ZIP file should appear automatically. If it does not, click the you can manually start your download link.
5. Click Save File and then click OK.
6. If you do not already have a Kemp ID, use the form at the bottom of this web page to create one.
2.2 Unzip the Disk Image
The Linux disk image has been tar gzipped as a sparse file. It must be unzipped as a sparse file to ensure proper operation. For example:
Kemp-360-Central-VM-v1.22.0.1580-RELEASE-Linux-KVM-XEN.zip
2.3 Deploy Kemp 360 Central
Kemp recommends using Virtual Machine Manager to deploy Kemp 360 Central. The steps below were documented using Virtual Machine Manager:
1. Click the Create a new virtual machine button.
2. Select Import existing disk image.
3. Click Forward then click Browse.
4. Browse to and select the disk file.
5. Select Generic as the OS type.
6. Select Generic as the Version.
7. Click Forward.
8. Enter a minimum of 4096 MB in the Memory text box.
9. Enter a minimum of 2 in the CPUs text box.
10. Click Forward.
11. Enter a Name for the Virtual Machine.
12. Select the appropriate network for the machine.
13. Click Finish.
2.4 Check the Virtual Machine Settings
Note that since Version 1.25.2, the default minimum Virtual Machine provisioning requirements for new installs have been updated as follows:
Resource | V1.24 and earlier firmware | V1.25.2 and later firmware |
CPU | Two cores | Four cores |
RAM | 4 GB | 8 GB |
Disk Storage | 40 GB | 250 GB |
Upgrades to Version 1.25.2 and later releases will not update existing Virtual Machine resources. To modify your current Virtual Machine configuration to conform to the above minimum values, contact Kemp Support.
There may be maximum configuration limits imposed by KVM such as maximum RAM per VM, Virtual network interface controllers (NICs) per VM, and so on. For further details regarding the configuration limits imposed by KVM, refer to the relevant KVM documentation.
2.5 Kemp 360 Central IP Address
After the VM boots, it should obtain an IP address through DHCP. Make a note of this address.
2.6 License and Configure Kemp 360 Central
You must now configure Kemp 360 Central to operate within the network configuration.
1. In an internet browser, enter the IP address you previously noted.
Ensure to enter https:// before the IP address.
2. A warning may appear regarding website security certificates. Click the continue/ignore option. The Kemp 360 Central Welcome page appears
3. Click Continue to proceed. The Kemp 360 Central End User License Agreement screen appears.
4. Read the license agreement and, if you are willing to accept the conditions therein, click Agree to proceed.
5. If using the Online licensing method, complete the fields and click License Now.
If using the Offline Licensing method, select Offline Licensing, obtain the license text, paste it into the License field, and click Apply License.
For detailed instructions on how to register for a Kemp ID and license Kemp 360 Central, refer to the Kemp 360 Central, Feature Description on the Kemp Documentation Page.
6. Set the desired administration password and click Set Password.
7. You should now connect to the Welcome page of Kemp 360 Central.
Last Updated Date
This document was last updated on 19 February 2019.